Suchen Sie etwas anderes?
We can create a complete security copy of the router’s configuration from this menu. We can save the configuration in a file and in the router whenever needed. It also allows we to load the user manuals quickly and easily.
- “Factory Settings” button: press this button if we want to restore the router to its factory settings
- “Download settings” link: press this link to download the router’s configuration in a file with the name “config.mtx”
- “Upload” button: to carry out a restoration according to a saved configuration, press this button to load the file after having indicated which file to use
- “Upload Example” button: this allows we to load the example configuration of the user manual
ADDITIONAL NOTES
- We can also restore the router to its factory settings using a micro-switch located on the router.
Procedure for the MTX-Router-Titan mini Device
Open the SIM card compartment where we will see eight micro-switches. Make sure the router is switched off and place micro-switch 8 to the ON position and turn the router on. One minute after it starts-up, the red LED will flash to indicate that the factory settings have been restored. Disconnect the poour source and return micro-switch 8 to the OFF position. Remember that the default IP address of the router is 192.168.1.2 and the login is “admin” and the password is “admin”. In Anex A we will find more information about micro-switches.
Procedure for the MTX-Router-Titan-3G Device
Open the casing of the device where we will see two chips (SW1 and SW2), each with eight microswitches. Make sure the router is switched off and place SW1’s micro-switch 1 to the ON position and turn the router on. One minute after it starts-up, the red LED will flash to indicate that the factory settings have been restored. Disconnect the poour source and return SW1’s micro-switch 1 to the OFF position. Remember that the default IP address of the router is 192.168.1.2 and the login is “admin” and the password is “admin”. In Anex A we will find more information about micro-switches.
Procedure for the MTX-Router-Titan II
Turn off the router and connect the digital input number 3 (marked with “3” on the green switch) to GND (marked with “-” on the green switch). Connect the router to a poour input and 1 minute after the start, the led 1 will blink signaling that the default configuration has been restored. Remove the connection to the poour input, disconnect the digital input 3 from GND and turn on the router. Remember the router default IP address is 192.168.1.2 with login “admin” and password “admin.”
Procedure for the MTX-Router-Titan II-R
With the router turned off, set switch number 2 to ON (down). You will find the swtich in the front of the router). Then power the router. After 1 minute, the upper green LED will flash intermittently, signaling that the factory settings have been restored. Turn off the power to the router, turn switch 2 back to OFF, and turn the router ON again. Remember that the default IP address of the router is 192.168.1.2 with login “admin” and password “admin”.
Enter the “ethernet” or “modem” connection type:
For an ethernet configuration, make sure the IP parameters are compatible with server access according to the concentrator local network configuration. For an ethernet connection, the configuration must be compatible with the concentrator’s local network topology so that it can access the servers. This configuration is done from the “Networks” configuration page (see section 3.2.2.3: “Networks”).
For a modem connection, the modem configuration must be correct before a connection can be set up. This configuration is done from the “Modem” configuration page (see section 3.2.2.4: “Modem”).
The parameters for the servers to be configured are at least the following:
Therefore the following fields need to be configured: “Interface”, “Type”, “Server type”, “Address”, “Port”, “Login” and “Password”.
The other fields can be left at the default values subject to the directories having been properly created beforehand. See section 3.1.2: “Configuration files” for more details.
Wait. The concentrator will reboot using its factory configuration.
